A chemical resistance chart is one of the most useful documents in a safety officer’s drawer and one of the most dangerous. It looks authoritative. Rows of chemicals, columns of glove materials, neat ratings from excellent to not recommended. People pick a cell, see a good rating, order the glove and consider the job done. Then a worker comes to first aid with a chemical burn under a glove that was rated excellent for that exact substance.
The chart was not wrong. It was answering a different question from the one being asked.
Three ways a chemical gets through
Before reading any chart, you need to know what it measures, because chemicals defeat protective materials in three different ways.
- Penetration is bulk flow through holes, seams, pinholes, zips and gaps. A glove with a split or a suit with a poorly sealed cuff fails by penetration, regardless of what it is made of.
- Permeation is the chemical dissolving into the material and diffusing through it at a molecular level. It happens through an intact glove with no visible change. The time it takes to be detected on the inside is the breakthrough time.
- Degradation is physical damage to the material, such as swelling, softening, hardening, cracking or loss of strength. A glove can degrade without permeating quickly, or permeate quickly without visibly degrading.
A simple chart with one rating per cell usually blends these together, or reports only degradation. That is the first reason it can mislead you.
How to read glove data properly
In Europe, chemical protective gloves are certified to EN ISO 374. Part 1 classifies gloves by permeation performance against a list of test chemicals, each identified by a letter. A Type A glove achieves a breakthrough time of at least 30 minutes against at least six of the listed chemicals, Type B at least 30 minutes against at least three, and Type C at least ten minutes against at least one. Permeation performance is graded in levels from 1 to 6, with level 6 meaning more than 480 minutes. Degradation is tested separately under EN 374 part 4, and resistance to micro organisms under part 5.
In the United States, there is no single federal glove classification equivalent to EN ISO 374. Manufacturers commonly publish permeation data from the ASTM F739 test method, and OSHA requires employers to select hand protection based on the hazards, the task and the performance characteristics of the glove.
The questions to ask of any chart
- Is this data for the specific glove model, at this thickness, or for the polymer in general? Generic polymer charts are a starting point, not a selection.
- Does the rating show breakthrough time, permeation rate and degradation separately?
- Was the test done with the pure chemical? Mixtures and solutions can behave very differently from their components, and a solvent can carry another chemical through a glove that would resist it on its own.
- What temperature was the test run at? Permeation speeds up as temperature rises, and a glove on a warm hand handling a warm liquid is not under laboratory conditions.
- Is the exposure continuous immersion or occasional splash? Most data assumes continuous contact on the outer surface.
The safety data sheet is the place to start. Section 8 should name a suitable glove material and often a breakthrough time. Treat a vague entry such as “wear suitable gloves” as a reason to call the supplier, not as an answer.
Common materials and their blind spots
Some general patterns hold well enough to steer a first selection, before you check the specific product data.
| Material | Generally good against | Known weaknesses |
|---|---|---|
| Nitrile | Oils, greases, many aliphatic solvents, many dilute acids and alkalis | Ketones such as acetone, many chlorinated and aromatic solvents |
| Natural rubber latex | Many water based solutions, dilute acids and alkalis | Most organic solvents, oils, latex allergy |
| Neoprene | Many acids and alkalis, some oils | Many aromatic and chlorinated solvents |
| Butyl | Ketones, esters, many highly corrosive acids | Aliphatic and aromatic hydrocarbons, fuels |
| Fluoroelastomer | Chlorinated and aromatic solvents | Ketones, some esters, cost and stiffness |
| Multilayer laminate | A very broad range of chemicals | Poor fit and dexterity, often worn under an outer glove |
Thin disposable nitrile gloves deserve a specific warning. They are designed for incidental splash, and for many solvents the breakthrough time is measured in minutes, sometimes less. Once splashed, they should be changed straight away. I have seen technicians wear the same pair all morning while handling solvents, which means a contaminated glove held against the skin for hours.
Eyes, face and body
Gloves get most of the attention, but a splash to the eye causes some of the worst injuries in chemical handling, particularly from strong alkalis.
Ordinary safety spectacles do not protect against liquid splash. Under EN 166, look for the field of use symbol 3, which indicates protection against liquid droplets and splashes and is only available on goggles and face shields. Under ANSI Z87.1 in the US, the equivalent marking is D3. For decanting, mixing and any work with corrosives, use sealed or indirectly vented goggles, with a face shield over them where there is risk of a larger splash. A face shield alone leaves the eyes exposed to liquid running in from the edges.
For body protection, Europe classifies chemical protective clothing into types. Type 3 is liquid tight against a pressurised jet, Type 4 is spray tight, and Type 6 gives limited protection against light splash. Type 5 covers airborne particles rather than liquids. In the US, the EPA protection levels A to D are used to describe ensembles for hazardous materials response, with Level A the highest. In both systems, the fabric rating is meaningless if the seams, closures and interfaces with gloves and boots leak. Taping cuffs and overlapping gloves over or under sleeves according to the direction of the likely splash makes a real difference.
Turning data into a decision
Base the selection on the actual task. Identify the chemicals, including mixtures and cleaning agents. Estimate contact type and duration. Shortlist materials from the safety data sheet and generic charts, then check the manufacturer’s own permeation data for the specific product. Where the chemical or mixture is unusual and the risk is high, ask the glove supplier to test it or run your own trial.
Then set a change schedule based on breakthrough time with a margin, not on when the glove looks worn. Train people to remove contaminated gloves without touching the outer surface. Make sure emergency eyewash is within immediate reach of where corrosives are handled.
The NIOSH Pocket Guide to Chemical Hazards is a sound neutral reference for the hazards of individual substances. Local regulation and a competent risk assessment decide the final answer, and the chart is evidence to feed that assessment, not a substitute for it.