Walk into most maintenance workshops and you will find a lockout station on the wall. Red padlocks on hooks, a pile of tags, a few hasps and a laminated sheet with the company logo. It looks like compliance. Then you ask a fitter to show you the isolation procedure for the press he worked on yesterday, and he points at the padlocks.
The padlock is the cheapest part of lockout tagout. What prevents a machine from starting while someone has an arm inside it is a written, tested procedure for that machine, carried out the same way every time by people who understand it. The hardware just holds the result in place.
What the rules actually require
In the United States, the OSHA standard on the control of hazardous energy, 29 CFR 1910.147, sets out what an employer must have. That means an energy control programme, documented procedures for specific equipment, training for authorised and affected employees, and a periodic inspection of each procedure at least once a year. The full text and guidance are on the OSHA control of hazardous energy pages. The standard does allow a tag alone instead of a lock, but only where the employer can show it gives protection equivalent to a lock, which in practice is a hard argument to win.
The United Kingdom and the European Union do not have a single lockout regulation in the same form. In the UK, the duty to provide means of isolating work equipment from every energy source sits in the Provision and Use of Work Equipment Regulations, and electrical isolation is covered by the Electricity at Work Regulations. HSE guidance on the safe isolation of plant and equipment, known as HSG253, is the reference most process industries work from. Across the EU, the work equipment directive and national law cover the same ground. The wording differs, but the expectation is identical. Isolate every energy source, secure the isolation, prove it, and control the return to service.
A procedure is specific or it is useless
A generic lockout procedure that says “isolate all energy sources” tells the person doing the work nothing they did not already know. What they need is a sheet for this machine that lists every energy source, where each isolation point is, what type of device locks it, how stored energy is released and how the isolation is verified.
Energy sources are where generic procedures fall apart. Electrical supply is obvious. The ones that hurt people are the others.
- Pneumatic supply, including the air left in the receiver and lines after the valve is shut.
- Hydraulic pressure held in accumulators, which can stay charged for hours.
- Gravity, meaning a raised platen, a ram, a counterweight or a load on a hoist.
- Springs under tension or compression in clamps, brakes and tensioners.
- Thermal energy in heated rolls, dies and process lines.
- Process fluids under pressure, steam, and anything that can flow back from connected plant.
- Rotating mass that keeps spinning after power is removed.
- A second electrical supply, such as a control circuit fed from another panel or a backup generator.
I have yet to audit a site where the machine specific procedures were complete on the first visit. The usual gap is a second supply that someone added during a modification and never put on the sheet. Procedures must be reviewed whenever equipment is changed, not just once a year.
Photographs help more than paragraphs
The best procedures I have used are one or two pages with photographs of each isolation point, each one numbered and labelled on the machine with a matching tag. A new starter can follow it. An experienced fitter can check it in thirty seconds. Long text procedures written for an auditor get skimmed and then ignored.
The sequence that actually protects people
The order of steps is consistent across almost every standard and guidance document, and each step has a common way of being skipped.
- Prepare. Read the procedure for that equipment. Identify every source before anything is touched.
- Notify. Tell operators and others affected that the machine is going down and why. Skipped when people are in a hurry, and that is when somebody restarts it from habit.
- Shut down normally. Stop the machine using its normal controls before isolating, so you do not break load on an isolator that is not designed for it.
- Isolate. Operate each energy isolating device. A stop button, an emergency stop or a control circuit interlock is not an energy isolating device.
- Apply locks and tags. Each person working on the equipment fits their own personal lock. One lock per person, one key per lock, the key stays with the person.
- Release stored energy. Bleed air and hydraulics, block or lower raised parts, release springs, let things cool or stop moving.
- Verify. Try to start the machine from its normal controls, and test electrical circuits with a proven voltage tester. Then return the controls to off.
Verification is the step that gets dropped most often, and it is the one that catches the wrong isolator, the mislabelled breaker and the second supply nobody knew about. If your people isolate and lock but do not try, they are trusting a label.
Groups, shifts and the lock nobody can find
Single person lockout on a single machine is the easy case. Most serious incidents involve something more complicated.
For group work, a lockbox system is standard. The authorised person isolates and locks each point, places the keys in a lockbox, and every member of the team applies their personal lock to the box. Nobody can get the isolation keys back until the last person has removed their lock. Contractors must be included in the same system, not running a parallel one with their own padlocks on different points.
Shift changes need a defined handover. The incoming person fits their lock before the outgoing person removes theirs, so the isolation is never left unprotected. Writing that down is easy. Making it happen at six in the morning when the night shift wants to go home takes supervision.
Then there is the lock left on by somebody who has gone home. Every programme needs a controlled removal procedure for this, and OSHA requires one. It normally means verifying that the person is not on site, making every reasonable attempt to contact them, having a supervisor or manager authorise removal, and making sure the person is told before they start work again. Bolt cutters on the say so of a production manager is not a procedure.
Keeping the programme alive
Lockout programmes decay quietly. Procedures go out of date. Personal locks get shared. Somebody starts using a single lock and a tag for a “quick job”. Training happens at induction and never again.
Annual inspection of each procedure, with someone competent actually watching an authorised person carry it out, is the most effective check I know. It is also a legal requirement under the US standard. Look at whether the steps match the machine, whether verification is done properly, and whether the person can explain why each step exists. Talk to the operators as well as the fitters, because they are the ones who will restart a machine they think has been left idle. The background to lockout tagout is simple enough. Doing it well every time is not, and a risk assessment for your own plant and your local regulation decide what the procedure must contain.