An electrician once told me his arc flash suit was rated 40, so he was safe to rack out any breaker in the building. He believed the number was a shield. It is not. The calorie rating on arc rated clothing tells you something narrow and specific about how much heat the fabric can block before the skin underneath is likely to burn. It tells you nothing about the pressure wave, the molten copper, the noise, the toxic gases or what happens if the incident energy at that panel is higher than anybody calculated.
Arc rated clothing is necessary for some work. It is never a reason to do that work live.
What the calorie rating measures
Arc ratings are expressed in calories per square centimetre, written as cal/cm². The figure on a garment is usually either the arc thermal performance value, known as ATPV, or the energy breakopen threshold, known as EBT, whichever is lower for that material. ATPV is the incident energy at which there is a 50 percent probability that heat passing through the fabric would cause the onset of a second degree burn, based on the Stoll curve. EBT is the incident energy at which the fabric is likely to break open.
Read that definition carefully. At exposure equal to the rating, there is a 50 percent chance of a second degree burn under the garment. The rating is a threshold, not a guarantee of no injury. That is why you choose clothing rated at or above the calculated incident energy, never below it, and why a margin is sensible.
The reference point for unprotected skin is 1.2 cal/cm², the incident energy commonly taken as the onset of a second degree burn. The arc flash boundary is defined as the distance from the arc source at which incident energy falls to that level. Inside the boundary, arc rated protection is required.
How the rating is used under NFPA 70E
In the United States, NFPA 70E is the consensus standard for electrical safety in the workplace, and OSHA relies on it in practice when assessing whether an employer has protected workers from electrical hazards. It allows two methods for selecting arc flash protection.
The first is the incident energy analysis method. An engineer calculates the incident energy at a specific working distance for each piece of equipment, usually using the IEEE 1584 calculation guide, and the result goes on the equipment label. Clothing is then selected with an arc rating at least equal to that figure.
The second is the arc flash PPE category method. Tables in NFPA 70E list common tasks and equipment types, with conditions such as maximum available fault current and fault clearing time. If the equipment falls within those parameters, a PPE category from 1 to 4 is assigned, each with a minimum arc rating.
| PPE category | Minimum arc rating |
|---|---|
| 1 | 4 cal/cm² |
| 2 | 8 cal/cm² |
| 3 | 25 cal/cm² |
| 4 | 40 cal/cm² |
Use one method or the other for a given piece of equipment. Mixing them, for example by using the category tables on a panel whose fault current exceeds the table’s conditions, is a common error. If the conditions are not met, the tables do not apply and you need an incident energy analysis.
The European picture
NFPA 70E does not apply in Europe. European employers work from the general risk assessment duties in their national law, standards on the operation of electrical installations such as EN 50110, and garment standards from the IEC 61482 series. Garments may carry an ATPV or EBT from the open arc test, which uses the same approach as the US method, or a box test class, APC 1 or APC 2, from a different test that uses a constrained arc in a box. The two results are not directly interchangeable, and a box test class is not a calorie value. In the UK, the Electricity at Work Regulations allow live work only where it is unreasonable for the conductor to be dead, where it is reasonable to work live, and where suitable precautions are taken.
What the rating does not buy you
An arc flash releases more than heat. Arc blast is a pressure wave that can throw people across a room, rupture eardrums and cause internal injury. Vaporised copper expands enormously and can carry molten metal and fragments of enclosure at speed. The light is intense enough to damage eyes. The gases produced are toxic. Arc rated clothing addresses the thermal hazard only, with some incidental protection from molten metal and fire.
Ratings also assume the whole system is worn properly. Weak points I have seen in the field include:
- Synthetic underwear or base layers that melt into the skin under an arc rated outer layer. Under layers must be non melting.
- Non arc rated rain jackets, high visibility vests and winter coats worn over arc rated clothing, which can ignite and burn on top of the protection.
- Arc rated shirts left open at the neck, sleeves rolled up, or a face shield without a balaclava, leaving the neck and sides of the head exposed.
- Layered garments assumed to add their ratings together. A layered system has to be tested as a system. You cannot add a 10 and a 12 and call it 22.
- Laundered garments contaminated with oil, grease or flammable residue, or repaired with non arc rated thread and patches.
Gloves, footwear, hearing protection and eye protection all need to be part of the selection. Leather gloves or rubber insulating gloves with leather protectors are commonly used, and NFPA 70E lists hearing protection in every arc flash PPE category.
The work that clothing cannot fix
Every arc flash conversation should start with whether the work can be done with the equipment in an electrically safe work condition. That means isolated, locked out, tested for absence of voltage and earthed where necessary. Most maintenance can be. The tasks that genuinely require live work, such as some diagnostic testing, are fewer than many maintenance teams claim.
Then reduce the energy itself. Incident energy depends on available fault current, working distance and, above all, clearing time. Engineering controls change those factors. Maintenance switching that speeds up protective device clearing during work, remote racking and remote switching, arc resistant switchgear, current limiting fuses and properly coordinated protection settings all reduce the energy or move the person away from it. Clothing does neither.
Finally, keep the study current. Incident energy labels go out of date when the utility supply changes, transformers are replaced, protection settings are adjusted or breakers are not maintained and clear slowly. A label that was right five years ago may now understate the hazard, and the suit selected from it may be inadequate.
Arc rated clothing is the last layer. Use it when the task truly requires live exposure, select it from a current analysis, wear it as a complete system, and let local regulation and a competent electrical risk assessment decide what work is permitted at all.